Sm420

Posted on  by admin
Reasoning:

Item 2 GM MUNCIE SM420 4 SPEED TRANSMISSION SIDE COVER C10 C20 C30 C40 K10 K20 K30 K40 2 - GM MUNCIE SM420 4 SPEED TRANSMISSION SIDE COVER C10 C20 C30 C40 K10 K20 K30 K40. Item 3 SM420 GM Chevy Transmission Rebuild Kit 54-67 4 Speed Rock Crawler 3 - SM420 GM Chevy Transmission Rebuild Kit 54-67 4 Speed Rock Crawler.

Get the best deals for sm420 transmission at eBay.com. We have a great online selection at the lowest prices with Fast & Free shipping on many items! 50-2402: GM SM420 4 speed manual transmission to the Jeep Dana 18 / 20 with 10 spline drive gear, (new SM420 spud shaft design adapter kit). The SM420 is the older heavy duty, granny, 4 speed transmission used in Chevy and GM trucks. The large cast iron case with large bulge on the passenger sidemakes it easy to identify. It is an excellent 4 speed to swap into a Jeep with a Chevy or Buick engine.


The SM420 has a first gear ratio of 7.05:1. When used with a 3spd transfer case and a 4.11 ring and pinion ratio, your final crawl ratio will be 67.5:1.
Availablility:
Sm420The SM420 was available from 1947-1967 in 1/2 to 2.5 ton chevy trucks. The only change made was in the last year when a reverse switch was added to illuminate reverse lights. Some of the parts for the SM420 have been discontinued by GM, so finding some of the parts, such as gears, is difficult.

Muncie Sm420


Required Parts:
To adapt the SM420 to the 2F (or F) and 3spd t-case you need:
3spd bellhousing (will bolt up to 2F)
3spd flywheel and pressure plate (I'm not sure if the 4spd will work)
Chevy 11' clutch disc (from something like a 75 4wd 1/2 ton chevy pu)Sm420
Special pilot bearing. It is the same inner (I think) and outer diameterfor the 3spd tranny, but the inner shaft is about 3/8'
longer, so it sticks out further. This isnecessary because the input shaft of the SM420 is a bit shorter than the3spd
Cruiser tranny.
Sleeve around the input shaft of SM420, where the throwout bearingrides.
Ring around the front bearing retainer of the 420. It isabout half an inch thick and has a wall thickness of about 1/2'. It
fits around the front bearing retainer and assuresthat the 420 sits snugly in the 3spd bellhousing.
On the back side all you need is the 3/4' adapter plate that you boltto the back of the tranny, then bolt the t-case to that.
The gear that rides on the output shaft of the 3spd tranny will slideright onto the output shaft of the SM420.
Discussion:
Sm420One thing about the 3/4' plate style adapter is that it rotates thet-case down so that the front output shaft flange is able to clear thetranny (it is still a close fit though and some people have to do a bitof grinding on the tranny). This means that your t-case will sitabout 1.5' lower than stock, which I find very helpful with the driveshaftangles on my spring-over.
Another thing that will have to be delt with is the linkage for the transfer-case. I have seen a few people build their own shifters, one type with two sticks, and the other like the Toyota single shifters. If you have an early model truck (like I have) you can use the stock vacuum shift for the 4wd, and just lengthen the rod going to the low range lever.

If you have a Cruiser that originally came with a 4spd tranny, you willhave to address the problem of having different driveshaft flanges betweenthe 3spd t-case and the stock pinion flanges.
There are 3 basic ways that I know of to make the change.
1. Split the driveshafts at the slip-yoke and use the 3spd driveshaftsection at the t-case end and the 4spd driveshaft section at the differentialend. Make sure to keep the U-joints in phase and to have the driveshaftbalanced before you install it.
2. Change the pinion flanges from the 4spd to the 3spd, they will boltright in. Then use the 3spd driveshafts
3. Change the output shaft flanges on the transfer case. Youwill only be able to do this on the rear. If you were to do thison the front I believe you would run into problems with interference between
the flange and your SM420.

Sm420 Pto

I think that is basically all of it. I got my adapters fromClassic Cruisers in Salida, CO. They were the most helpful and seemedto be reasonably priced.
This conversion is at the owners risk and I assume no part in any ill fate that might occur because of my directions. Use at your own risk.
Back to Land Cruiser Page