P0846 Nissan

Posted on  by admin

The OBD2 Code Information Be Applicable For Nissan: 2013 Nissan Pathfinder,2013 Nissan Murano,2013 Nissan Juke Nismo,2013 Nissan GT-R,2013 Nissan Altima Sedan,2013 Nissan Almera,2013 Nissan 370Z,2012 Nissan Tiida,2012 Nissan Sunny,2012 Nissan Qashqai,2012 Nissan Murano,2012 Nissan Micra ELLE,2012 Nissan Micra DIG-S,2012 Nissan Maxima,2012 Nissan Juke Shiro,2012 Nissan GT-R,2012 Nissan. Nissan service manual on transmission has listed out some elaborate steps to identify the issue with low pressure. Make sure your mechanic follows those steps. I really hope that it is a simple fix for your problem. Let me know how it went with your car. Mine was 2011 Altima 3.5 SR.

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / P0846 Transmission fluid pressure SEN/SW B

DTC Logic

DTC DETECTION LOGIC

DTCCONSULT screen terms (Trouble diagnosis content)DTC detection conditionPossible causes
P0846TRANSMISSION FLUID PRESSURE SEN/SW B (Transmission Fluid Pressure Sensor/Switch B Circuit Range/Performance)The detection conditions continuously for 5 seconds or more under the following diagnosis conditions:

Diagnosis conditions

  • Selector lever: “D” position
  • The primary pulley speed experienced 306 rpm or more and the secondary pulley speed experienced 230 rpm or more at least once.
  • Stop lamp switch: OFF
  • Wheel spin is not being detected.
  • The rate of change in pulley ratio: Between −0.09 and +0.09 inclusive
  • Solenoid valve output current: 750 mA or more
  • GND short diagnosis of the solenoid valve circuit is not satisfied.
  • TCM power supply voltage: More than 11 V

Detection conditions

  • After the value of “Actual secondary pressure − Target secondary pressure” exceeds 0.675 MPa:

The rate of change in vehicle speed [km/h (MPH)]: Between −49 (−30) and +49 (+30) inclusive

The rate of change in accelerator pedal angle: Between −1.3/8 and +1.3/8 inclusive

  • Secondary pressure sensor
  • Control valve assembly

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

Nissan

1.PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Start the engine.
  2. Shift the selector lever to “D” position.
  3. Drive the vehicle at a constant velocity of 40 km/h (25 MPH) at lease for 10 seconds.

CAUTION:

At the same time, the accelerator pedal angle must be maintained constant.

  1. Stop the vehicle.
  2. Check the first trip DTC.

Is “P0846”detected? YES >> Go to TM-192, 'Diagnosis Procedure'.

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK TCM INPUT SIGNAL

P0846 Nissan
  1. Start the engine.
  2. Check voltage between TCM connector terminal and ground.

Is the inspection
result normal? YES >> Check intermittent incident. Refer to GI-39, 'Intermittent Incident'.

NO >> There is a malfunction of secondary pressure sensor value. Replace transaxle assembly. Refer to TM-283, 'Removal and Installation'.

P0847 TRANSMISSION FLUID PRESSURE SEN/SW B

DTC Logic

DTC DETECTION LOGIC

DTCCONSULT screen terms (Trouble diagnosis content)DTC detection conditionPossible causes
P0847TRANSMISSION FLUID PRESSURE SEN/SW B (Transmission Fluid Pressure Sensor/Switch B Circuit Low)The secondary pressure sensor voltage is 0.09 V or less continuously for 5 seconds or more under the following diagnosis conditions:

Diagnosis conditions

  • CVT fluid temperature: More than −20В°C (− 4В°F)
  • TCM power supply voltage: More than 11 V
  • Harness or connector (Secondary pressure sensor circuit is open or shorted to ground)
  • Secondary pressure sensor
  • Control valve assembly

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

With CONSULT


  1. Start the engine.
  2. Select “Data Monitor” in “TRANSMISSION”.
  3. Select “FLUID TEMP”.
  4. Maintain the following conditions for 10 seconds or more.

FLUID TEMP : −19В°C (−2.2В°F) or more

  1. Check the first trip DTC.

With GST


  1. Start the engine and wait for at least 10 seconds.

CAUTION:

When the ambient temperature is −20В°C (−4В°F) or less and the engine is cold, warm up the engine for approximately 5 minutes.

  1. Check the first trip DTC.

Is “P0847”detected? YES >> Go to TM-194, 'Diagnosis Procedure'.

NO >> INSPECTION END

P0846 Nissan

Diagnosis Procedure

1.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector and CVT unit connector.
  3. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.

Is the inspection
result normal?

YES >> GO TO 2.

NO >> Repair or replace malfunctioning parts.

2.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 2)

Check continuity between TCM harness connector terminals and ground.

Is the inspection
result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts.

3.CHECK TCM INPUT SIGNALS

  1. Connect all connectors removed.
  2. Start the engine.
  3. Check voltage between TCM connector terminal and ground.

Is the inspection
result normal? YES >> Check intermittent incident. Refer to GI-39, 'Intermittent Incident'.

NO >> There is malfunction of secondary pressure sensor. Replace transaxle assembly. Refer to TM- 283, 'Removal and Installation'.

P0848 TRANSMISSION FLUID PRESSURE SEN/SW B

DTC Logic

DTC DETECTION LOGIC

P0846
DTCCONSULT screen terms (Trouble diagnosis content)DTC detection conditionPossible causes
P0848TRANSMISSION FLUID PRESSURE SEN/SW B (Transmission Fluid Pressure Sensor/Switch B Circuit Low)The secondary pressure sensor voltage is 4.7 V or more continuously for 5 seconds or more under the following diagnosis conditions:

Diagnosis conditions

  • CVT fluid temperature: More than −20В°C (− 4В°F)
  • Secondary pressure target value: 5.7 MPa or less
  • TCM power supply voltage: More than 11 V
  • Harness or connector (Secondary pressure sensor circuit is shorted to power supply)
  • Secondary pressure sensor
  • Control valve assembly

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, the ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

With CONSULT


  1. Start the engine.
  2. Select “Data Monitor” in “TRANSMISSION”.
  3. Select “FLUID TEMP”.
  4. Maintain the following conditions for 10 seconds or more.

FLUID TEMP : −19В°C (−2.2В°F) or more

  1. Check the first trip DTC.

P0846 Nissan Versa

With GST


  1. Start the engine and wait for at least 10 seconds.

CAUTION:

When the ambient temperature is −20В°C (−4В°F) or less and the engine is cold, warm up the engine for approximately 5 minutes.

  1. Check the first trip DTC.

Is “P0848”detected? YES >> Go to TM-196, 'Diagnosis Procedure'.

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK SECONDARY PRESSURE SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect CVT unit connector.
  3. Turn ignition switch ON.
  4. Check voltage between CVT unit harness connector terminal and ground.

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace malfunctioning parts.

2.CHECK SECONDARY PRESSURE SENSOR SIGNAL CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.

Is the inspection
result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts.

3.CHECK TCM INPUT SIGNALS

  1. Connect all connectors removed.
  2. Start the engine.
  3. Check voltage between TCM connector terminal and ground.
P0846 Nissan

Is the inspection
result normal? YES >> Check intermittent incident. Refer to GI-39, 'Intermittent Incident'.

P0846 Nissan Versa

NO >> There is a malfunction of secondary pressure sensor. Replace transaxle assembly. Refer to TM- 283, 'Removal and Installation'.

P0846 Jeep

P0746 Pressure control solenoid A
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0746 PRESSURE CONTROL SOLENOID A (Pre ...
P0863 TCM Communication
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0863 TCM COMMUNICATION (TCM Communicatio ...

Code Po 846

Other materials:

Service data and specifications (SDS)
General Specifications Brake Pedal Check Valve Brake Booster Front Disc Brake Rear Drum Brake Rear Disc Brake ...

P0846 Nissan Versa 2012

P0137 HO2S2
DTC Logic DTC DETECTION LOGIC The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching time. To judge the malfunctions of heated oxygen ...

Engine compartment
CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not come on, check for an open fuse. Be sure the ignition switch and the headlight switch are ...

© 2014-2021 Copyright www.nisentra.com
Click Here to visit the Transmission Rebuilders Network Home Page

Are you having problems fixing diagnostic trouble code (DTC) P0846 Transmission Fluid Pressure Sensor/Switch B Circuit Range/Performance? Are you looking for code P0846 troubleshooting help, code P0846 diagnosis tips, code P0846 diagnostics or code P0846 technical information? Do you just have code P0846 questions and need some answers about Transmission Fluid Pressure Sensor/Switch B Circuit Range/Performance? Do you have diagnostic trouble code (DTC) P0846 Transmission Fluid Pressure Sensor/Switch B Circuit Range/Performance and need troubleshooting information?

The Transmission Rebuilders Network is the place where the industries best transmission rebuilders work together to help solve the most complex automatic transmission problems. Whether you need P0846 diagnostic tree information, P0846 diagnosis tips, P0846 technical information, P0846 diagnostics, P0846 troubleshooting help, or just answers to your code P0846 question, the Transmission Rebuilders Network is the place to go!

Technical help for the following transmissions;

P0846 Nissan


Code P0846 Nissan Versa

Click Here to visit the Transmission Rebuilders Network Home Page