P0845

Posted on  by admin
  1. P0845 Nissan Sentra 2007
  2. P0845 Nissan Murano 2007
  3. P0845 Nissan
  4. P0845 Error Code

P0845 Chrysler Description The transmission fluid pressure sensor B (primary pressure sensor) detects primary pressure of Continuously Variable Transmission (CVT) and sends Transmission Control Module (TCM) the signal. P0845 Transmission Fluid Pressure Sensor B. The OBD2 Code Information Be Applicable For Mitsubishi: 2013 Mitsubishi GR-HEV,2011 Mitsubishi i-MiEV,2011 Mitsubishi RVR. P0845 Transmission Fluid Pressure Sensor/ Switch B Circuit - Chrysler 2005 300 question.

Click Here to visit the Transmission Rebuilders Network Home Page

Are you having problems fixing diagnostic trouble code (DTC) P0845 2/4 Hydraulic Pressure Test Failure? Are you looking for code P0845 troubleshooting help, code P0845 diagnosis tips, code P0845 diagnostics or code P0845 technical information? Do you just have code P0845 questions and need some answers about 2/4 Hydraulic Pressure Test Failure? Do you have diagnostic trouble code (DTC) P0845 2/4 Hydraulic Pressure Test Failure and need troubleshooting information?

The Transmission Rebuilders Network is the place where the industries best transmission rebuilders work together to help solve the most complex automatic transmission problems. Whether you need P0845 diagnostic tree information, P0845 diagnosis tips, P0845 technical information, P0845 diagnostics, P0845 troubleshooting help, or just answers to your code P0845 question, the Transmission Rebuilders Network is the place to go!

Technical help for the following transmissions;


Click Here to visit the Transmission Rebuilders Network Home Page

Description

The transmission fluid pressure sensor B (primary pressure sensor) detects primary pressure of CVT and sends TCM the signal.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

P0845 Nissan Sentra 2007

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Make sure that output voltage of line temperature sensor is within the range below.

ATF TEMP SEN : 1.0 – 2.0 V

If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid)

4. Start engine and wait for at least 5 consecutive seconds.

Follow the procedure “With CONSULT-III”.

Is “P0845 TR PRS SENS/B CIRC” detected? YES >> Go to TM-166, 'Diagnosis Procedure'.

NO >> Check intermittent incident. Refer to GI-42, 'Intermittent Incident'.

Diagnosis Procedure

1.CHECK INPUT SIGNAL

1. Start engine.

2. Check voltage between TCM harness connector F16 terminal 14 and ground.

3. Turn ignition switch OFF.

Is the inspection result normal? YES >> GO TO 8.

NO >> GO TO 2.

2.CHECK SENSOR POWER AND SENSOR GROUND

P0845 dodge

1. Turn ignition switch ON.

2. Check voltage between TCM harness connector F16 terminal 25 and 26.

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 5.

3.CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR B (PRIMARY PRESSURE SENSOR)] (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector and CVT unit harness connector.

3. Check continuity between TCM harness connector F16 (A) terminal 14 and CVT unit harness connector F46 (B) terminal 25.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR B (PRIMARY PRESSURE SENSOR)] (PART 2)

Check continuity between TCM harness connector F16 terminal 14 and ground.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace damaged parts.

5.CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector and CVT unit harness connector.

3. Check continuity between TCM harness connector F16 (A) terminal 25, 26 and CVT unit harness connector F46 (B) terminal 19, 20.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace damaged parts.

6.CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART 2)

Check continuity between TCM harness connector F16 terminal 25, 26 and ground.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace damaged parts.

P0845 Nissan Murano 2007

7.CHECK TCM

1. Replace same type TCM. Refer to TM-254, 'Exploded View'.

2. Connect each connector.

3. Perform “DTC CONFIRMATION PROCEDURE”. Refer to TM-166, 'DTC Logic'.

Is “P0840 TR PRS SENS/A CIRC” detected? YES >> Replace transaxle assembly. Refer to TM-259, 'Exploded View'.

NO >> Replace TCM. Refer to TM-254, 'Exploded View'.

8.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, 'Exploded View'.

NO >> Repair or replace damaged parts.

P0845 Nissan

P0841 pressure sensor function
Description Using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal, TCM changes the operating pressure of the pr ...

P0845 Error Code

P0868 secondary pressure down
Description The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM. DT ...
Other materials:

Camshaft
Removal and Installation 1. Camshaft bracket (No.1) 2. Washer 3. Front cover (partial view) 4. Chain guide 5. Chain tensioner 6. O-ring(s) 7. Chain tensioner spring 8. Chain tensioner plunger 9. IVT control solenoid valve 10. IVT control cover 11. Camshaft sprocket (EXH) 12. Camshaft ...

Precaution
Supplemental Restraint System (SRS) 'AIR BAG' and 'SEAT BELT PRE-TENSIONER' The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front ...

NISSAN Intelligent Key®
Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intelligent Key system components and NISSAN Vehicle Immobilizer System components. As many as 4 Intelligent Keys can be registered and used with one vehicle. The new keys must be registered by a ...